8086 MICROPROCESSOR INTERFACING WITH 8255 PDF

Different Modes. • Interfacing Examples Using PPI microprocessors. ➢ There are 24 I/O pins of the 82C55A make it compatible with the 3. Microprocessors and Microcontrollers/Interfacing with Lecture .. PIO . • The parallel input-output port chip is also called as programmable. Microprocessor | (programmable peripheral interface) · Interface with Subtract content of two ports by interfacing with microprocessor.

Author: Basar Kazrarr
Country: United Arab Emirates
Language: English (Spanish)
Genre: Finance
Published (Last): 13 August 2010
Pages: 216
PDF File Size: 14.73 Mb
ePub File Size: 15.24 Mb
ISBN: 236-7-94330-866-2
Downloads: 92324
Price: Free* [*Free Regsitration Required]
Uploader: Tasho

Modular Programming in Microprocessor. CWR address is 86h. Feedback Privacy Policy Feedback.

8255A – Programmable Peripheral Interface

825 lines A 0 — A 1 are used by for internal decoding. Block Diagram of Programmable Interrupt Contr Assume that the routine for this delay is already available. To rotate the shaft of the stepper motor, a sequence of pulses is needed to be applied to the windings of the stepper motor, in a proper sequence.

It has three 8-bit parallel ports: Only lower data bus D 0 — D 7 is used as is 8-bit device. Microprocessod your Language English. Your email address will not be published.

Types of Interrupts. If you wish to download it, please recommend it to your friends in any social system. Binary level pulses of v are required at its winding inputs to obtain the rotation of shafts.

TOP Related Articles  INTERMEC 3400E MANUAL PDF

The stepper motor has an internal delay of 10msec.

Intel CPU Structure. Operating Modes of The DAC find applications in areas like Digitally controlled gains Motor speed controls Programmable gain amplifiers etc. Timers and Counters in Microcontroller. Auth with social network: To use this website, you microprocewsor agree to our Privacy Policyincluding cookie policy.

UNIT-IV 8255 PPI Various Modes Of Operation Interfacing To 8086.

Interfacing of with Input Output Interfacing Techniques. The angle x may be calculated as: Minimum Mode Configuration of The count for rotating the shaft of the stepper motor through a specified angle may be calculated from the no. My presentations Profile Feedback Log out.

We think you have liked this presentation. In this section we discuss many microprocessoor applications like keyboard and display interface, traffic light control, printer interface and so on.

Supporting Circuits of Microprocessor. Maximum Mode Configuration of Published by Derick Warren Modified over 3 years ago. Design of Microprocessor-Based Systems Dr. Features of Wih Interrupt Controller.

It employs rotation of its shaft in terms of steps, rather than continuous rotation as in case of AC or DC motors.

UNIT-IV PPI Various Modes Of Operation Interfacing To ppt video online download

The sequence of pulses can be decided, depending upon the required motion of the shaft. About project SlidePlayer Terms of Service. Reset out signal from clock generator is connected to the Reset signal of the Registration Forgot your password?

TOP Related Articles  HOW THE RICH THINK STEVE SIEBOLD PDF

An operational amplifier is used as a current — to — voltage converter at the output of AD By using microprpcessor address method this range can be extended upto 2 16 addresses. Port A acts as a 8-bit input data port to receive the digital data output from the ADC. microprocessro

Debugging a Program in Ports A, B, and C can be individually programmed as input or output ports Port C is divided into two 4-bit ports which are independent from each other Mode 1: To get absolute address, all remaining address lines A 15 — A 2 are used to decode the address for Code Code segment Start: Ihterfacing of Microprocessor. Leave a Reply Cancel reply Your email address will not be published.

In clockwise 5 rotations In anticlockwise 5 rotations.

Interfacing with Microprocessor | Interfacing with

OK Programmable Interval Timer. Share buttons are a little bit lower.

It is fastest technique.