KSPA Transistor Datasheet pdf, KSPA Equivalent. Parameters and Characteristics. NPN Epitaxial Silicon Transistor. Absolute Maximum RS=IKΩ, f=1KHz. 4. dB. KSPA Design. This datasheet contains the design specifications for. The KSPA is manufactured in a plastic TO case. When looking at the flat side with the leads pointed downward, the three leads emerging from the.
|Genre:||Health and Food|
|Published (Last):||25 October 2015|
|PDF File Size:||19.37 Mb|
|ePub File Size:||10.22 Mb|
|Price:||Free* [*Free Regsitration Required]|
The capacitors C1 and C2 are simply used for filtering purpose. There are many types of amplifier circuits that are possible with transistor but this is the most commonly used one because it is very good in amplifying low frequency voltage signals like audio signals.
One of the most default and primary function of a transistor is to act transisfor a switch. The resistor R1 is called the Transisotr resistor and is very important to drive a transistor, it limits the base current and failing to use one might damage the transistor permanently. Every transistor has a gain h FE associated with it, which can be used to amplify voltage or current. The maximum amount of current that could flow through the Collector pin is mA, hence we cannot connect loads that consume more than mA using this transistor.
KSPA Datasheet(PDF) – Fairchild Semiconductor
In this type of circuit, the Emitter and the Base pin of the transistor should be commonly connected to a same voltage, so we have connected it to the Ground potential using two resistors R4 and R3. KSPA has a gain value of tothis value determines the amplification capacity of the transistor.
When base current is removed the transistor becomes fully off, this stage is called as the Cut-off Region.
Again the values of the resistor mentioned above are only for reference commonly used you have to design your own circuit based on the application and transistor you are using. TL — Programmable Reference Voltage.
KSPA Datasheet, Equivalent, Cross Reference Search. Transistor Catalog
When this transistor is fully biased then it can allow a maximum of mA to flow across the collector and emitter. But there are two important features that distinguish both. Normally this type of transistor will either be used as a switch or as an amplifier, both of which is discussed below. The resistor R2 is used to limit the current though the collector of the transistor and is not mandatory. The vales of the Resistor in the above image are only for reference and are not accurate.
KSPA can allow collector current upto mA and also has power dissipation of mW which can be used to drive larger loads than compared with BC KSPA is a NPN transistor hence the collector and dtaasheet will be left open Reverse biased when the base pin is held at ground and will be closed Forward biased when a signal is provided to base pin.
Applications General purpose NPN transistor Can be used to switch high current upto mA loads It can also be used in the various switching applications. The base pin of the transistor has to be biased with a voltage; this voltage transishor provided by the potential divider network formed by the resistors R4 and R6.
Transistor as Amplifier Another Common application of a Transistor is as amplifiers. However this type of amplifiers datsaheet many drawback and if you are looking for some serious amplification applications then you should look into Op-Amps which are nothing but a package of many transistors put to gather with amplification as its sole purpose.
Another Common application of a Transistor is as amplifiers.
The transistor will begin to conduct when the voltage across the Base and Emitter pin exceeds 0. It is very similar to a mechanical switch but here we will control the switch using electric signals.
So if you looking for an NPN transistor that datashert switch loads of higher current then KSPA might the right choice for your project. To bias a transistor we have to supply current to base pin, this current I B should be limited to 5mA. Submitted by admin on 24 June